Next section
Next page: →
Chapter 1: General Information
1.1 Installation Instructions
This manual provides installation instructions for the following ED50/ED100/ED250 (fine cover) door configurations. Reference Para. 2.2 and Para. 2.3 for illustrations.
Single Doors
- RH and LH pull
- RH and LH push
- RH and LH pull as push
Double Doors
- Pull
- Push
- Pull as push
- Double egress
Companion Doors
- Push
- Pull
For ED50/ED100/ED250 Fine Cover and Header Setup and Troubleshooting, reference the ED50/ED100/ED250 Setup and Troubleshooting Manual DL4617-002.
Manuals are available for review, download, and printing on the dormakaba.us website.
1.1.3 Dimensions
Unless otherwise specified, all dimensions are given in both inches (") and [mm].
1.1.4 Building Codes and Standards
ED50/ED100/ED250 installation: observe applicable national and local building codes.
1.1.5 Symbols used in these instructions
This symbol warns of hazards which could result in personal injury or threat to health.
This symbol warns of a potentially unsafe procedure or situation.
Draws attention to important information presented in this document.
Clarifies instructions or other information presented in this document.
Chapter 2: Product Overview
2.1 Types of Door Panels
Table 2.1.1 ED50 Low Energy Door Panel
| Parameter | Imperial | Metric |
|---|---|---|
| Maximum door width | 48" | [1219 mm] |
| Maximum door weight | 220 lbs | [100 kg] |
Table 2.1.2 ED100 Low Energy Door Panel
| Application | Max Width | Max Weight |
|---|---|---|
| Exterior | 48" [1219 mm] | 220 lbs [100 kg] |
| Interior | 48" [1219 mm] | 600 lbs [272 kg] |
Table 2.1.3 ED100 Full Energy Door Panel
| Maximum door width | 48" [1219 mm] |
| Maximum door weight | 220 lbs [100 kg] |
Table 2.1.4 ED250 Low Energy Door Panel
| Application | Max Width | Max Weight |
|---|---|---|
| Exterior | 48" [1219 mm] | 600 lbs [272 kg] |
| Interior | 48" [1219 mm] | 800 lbs [317 kg] |
Table 2.1.5 ED250 Full Energy Door Panel
| Maximum door width | 48" [1219 mm] |
| Maximum door weight | 320 lbs [272 kg] |
To insure proper suitability for exterior door use, the following topics must be addressed in the context of the door application setting:
- For site-specific use factors such as high wind conditions and/or building pressure consult the factory.
- Door width, height, weight, and usage patterns.
- Observable prevailing conditions at the opening under which the operator is expected to perform. In some instances, this may require increased force settings to counteract these conditions.
- Door mounted presence sensors: When attempting to overcome these forces, it is strongly suggested that door mounted presence sensors be employed to enhance pedestrian safety through the opening.
The ED50/ED100/ED250 with fine cover must be installed on an interior building surface.
2.2 Single & 2.3 Double Door Configuration Examples
Refer to installation diagrams for the following configurations:
- LH push / RH push
- LH deep pull / RH deep pull
- LH pull as a push / RH pull as a push
- Double egress
- Companion door (push/pull without cover)
2.4 - 2.6 Operator, Terminals & Guide Pins
Sections 2.4 through 2.6 detail the specific operator units (ED50 vs ED100/ED250) and accessory terminals.
- #12 x 2 1/2" Phillips FHWS (DF0670 000)
- 1/4-20 x 1 1/2" PFHMS (DF0671-000)
Safety Information & Labels
Essential safety checks for Automatic Swinging Doors and Low Energy Swinging Doors.
Inspect for and complies with ANSI A156.19 (Low Energy) or A156.10 (Full Energy). Have door inspected by an AAADM certified inspector at least annually.
Daily Safety Checks
- Activate the door. Door should open at a slow smooth pace (4 or more seconds) and stop without impact.
- Check Open Time. Door must remain fully open for a minimum of 5 seconds before beginning to close.
- Check Closing. Door should close at a slow, smooth pace (4 or more seconds) and stop without impact.
- Inspect Floor. It should be clean with no loose parts that might cause user to trip or fall. Keep traffic path clear.
- Inspect Condition. Evidence of damage or missing signage. Hardware should be in good condition.
DO NOT USE DOOR if it fails any of these safety checks or if it malfunctions in any way. Call a qualified automatic door service company.
Required Decals
- "Automatic Caution Door" (DD0586-010)
- "Activate Switch to Operate" (DD0758-010)
- "Push to Operate" (DD0762-010)
- "Pull to Operate" (DD0762-020)
- "Do Not Enter" (DD0739-020)
- AAADM Safety Label
2.8 Fine Cover Kits
| Part Number | Description |
|---|---|
| DK3401-01X | Fine cover kit basic |
| DK3401-05X | Fine cover professional single |
| DK3401-07X | Fine cover professional pair |
Kit includes items such as fine covers, end cap sets, spindle covers, backplates, logo plates, and templates.
Hardware and Accessories
2.10 Axle Extensions
- 20 mm axle extension (DC4679-001) - 3/4"
- 30 mm axle extension (DC4679-002) - 1 1/8"
- 60 mm axle extension (DC4679-003) - 2 3/8"
- 90 mm axle extension (DC4679-004) - 3 9/16"
Push & Pull Arm Kits
- Standard push arm (DC4677-01X)
- Deep push arm (DC4677-02X)
- Pull arm (DC4678-01X)
- Deep pull arm (DC4678-02X)
2.16 Connection Cables
Includes Sync cables and Power connect cables of various lengths (e.g., DX3485-030 for 2030mm sync).