Next section
Next page: →4.1 Diagrams
The following diagrams outline the drive drawings and installation diagrams for various configurations of the ECdrive T2 system.
| Drawing no. | Type | Name / Description |
|---|---|---|
| 70518-0-001 | Drive drawing | ECdrive T2, drives |
| 70518-ep01 | Installation diagram | ISO (toughened safety glass) glass fitting, 1-leaf |
| 70518-ep02 | Installation diagram | ISO (toughened safety glass) glass fitting, 2-leaf |
| 70518-ep03 | Installation diagram | ESG (toughened safety glass) glass fitting, 1-leaf |
| 70518-ep04 | Installation diagram | ESG (toughened safety glass) glass fitting, 2-leaf |
| 70518-ep17 | Installation diagram | ISO (toughened safety glass) post-rail construction 1-leaf |
| 70518-ep18 | Installation diagram | ISO (toughened safety glass) post-rail construction 2-leaf |
| 70518-ep19 | Installation diagram | ESG (toughened safety glass) post-rail construction 1-leaf |
| 70518-ep20 | Installation diagram | ESG (toughened safety glass) post-rail construction 2-leaf |
| 70518-ep21 | Installation diagram | ISO Lock A 1-leaf |
| 70518-ep22 | Installation diagram | ISO Lock A 2-leaf |
| 70518-ep23 | Installation diagram | ISO Lock M 1-leaf |
| 70518-ep24 | Installation diagram | ISO Lock M 2-leaf |
| 70518-ep33 | Installation diagram | ISO post-rail construction Lock A 1-leaf |
| 70518-ep34 | Installation diagram | ISO post-rail construction Lock A 2-leaf |
| 70518-ep35 | Installation diagram | ISO post-rail construction Lock M 1-leaf |
| 70518-ep36 | Installation diagram | ISO post-rail construction Lock M 2-leaf |
| 70518-ep37 | Installation diagram | Protective leaf attachment |
| 70518-ep38 | Installation diagram | ISO-ESG (toughened safety glass) side panel on site |
| 70518-ep39 | Installation diagram | Wooden leaf on site 1-leaf |
| 70518-ep40 | Installation diagram | Wooden leaf on site 2-leaf |
| 70484-ep04 | Installation diagram | Safety leaf for sliding door drives |
| 70518-2-0203 | Component drawing | Cover 100 × 132 |
| 70518-2-0204 | Component drawing | Cover 150 × 132 |
| 70715-1-0159 | Assembly group drawing | Continuous floor guide |
Note: The diagrams are subject to change without notice. Use only the most recent version.
4.2 Tools and Aids
Ensure you have the following tools available for installation and service:
| Tool | Size / Specification |
|---|---|
| Tape measure | - |
| Marking pen | - |
| Torque spanner | - |
| Allen key | 2 mm, 2.5 mm, 3 mm, 4 mm, 5 mm, 6 mm |
| Open-ended spanner | 8 mm, 10 mm, 13 mm, 15 mm |
| Screwdriver set | Slotted up to 6 mm; Phillip’s head PH2 and PH4 |
| Torx key | Tx 20; bit length at least 110 mm |
| Side-cutting pliers | - |
| Crimping pliers for cables | - |
| Wire stripper | - |
| Display programme switch | Service terminal ST220 / GEZEconnects |
| Ring spanner | 8 mm, 10 mm |
4.3 Torques
The specific torque values are provided with each respective installation step in the full manual.
4.4 Components and Assembly Groups
Please refer to the ep-drawing for the required installation situation and specific drive drawings referenced in Table 4.1.