Next section
Next page: →Models: DCU1-NT, DCU1-2M-NT, DCU1, DCU1-2M
1. Introduction
GEZE User Manual Section 3 & 4
Applicable Models: DCU1-NT, DCU1-2M-NT, DCU1, DCU1-2M
1.1 Symbols and illustrations
Warning notices
Warning notices are used in these instructions to warn you of personal injury and property damage.
| Warning symbol | Warning word | Meaning |
|---|---|---|
| ⚠️ | WARNING | Danger to persons. Non-compliance may result in death or serious injuries. |
| ⚠️ | CAUTION | Danger to persons. Non-compliance can result in minor to medium injuries. |
Further symbols and illustrations
Important information and technical notes are highlighted to explain correct operation.
| Symbol | Meaning |
|---|---|
| (i) Important note | Means "important note"; information about avoiding property damage. |
| (+) Additional Information | Means "additional Information". The user's attention should be drawn to important addition information. There is no danger to persons or property, but it is particularly useful to read the additional information carefully. |
| ✗ Action | Symbol for an action: This means you have to do something. If there are several actions to be taken, keep to the given order. |
| Escape route | Escape and rescue route; means the sliding door cannot be operated in escape and rescue routes. |
| No escape route | Not an escape and rescue route; means the sliding door cannot be operated in escape and rescue routes. |
| BOBO Break-out | Means that the door leaves and side panels are equipped with a break-out function. |
| No break-out | Means the function is not possible for break-out doors. |
1.2 Product liability
In accordance with the manufacturer's liability for their products as defined in the German "Produkthaftungsgesetz" (Product Liability Act), the information contained in this user manual (product information and proper use, misuse, product performance, product maintenance, obligations to provide information and instructions) is to be noted and followed. Failure to comply releases the manufacturer from his statutory liability.
1.3 Special cases
In certain cases, deviations from the information given in this user manual may occur. Examples:
- Special wiring
- Special function settings (parameters)
- Special software
1.4 More detailed information
Information for commissioning and maintenance can be found in the wiring diagram and in the installation instructions for the various automatic sliding doors.
1.5 Terms
| Term | Explanation |
|---|---|
| Activation device inside (KI) | Push button, switch or movement detector for activating the door drive. The activation device is located within the room enclosed by the door. Activation function in the "Automatic" and "Exit only" modes of operation. The activation device does not have any function in the "Night/Locked" and "Off" mode of operation. |
| Activation device outside (KA) | Push button, switch or movement detector for activating the door drive. The activation device is located outside the room enclosed by the door. Activation function in the "Automatic" mode of operation. The activation device does not have any function in the "Exit only", "Night/Locked" and "Off" mode of operation. |
| Activation device authorised (KB) | Access control function (for example key switch or card reader) used by authorised persons to activate the door drive. The activation function is active in the "Automatic" "Exit only", "Night/Locked" and "Off" modes of operation. |
| Opening safety sensor (SIO) | Presence detector (e.g. active infrared light sensor) for protecting the swinging range of the door in the opening direction. The sensor secures the secondary closing edge. |
| Closing safety sensor (SIS) | Presence detector (e.g. active infrared light sensor) for protecting the swinging range of the door in the closing direction. The sensor secures the main closing edge on the inside and outside. |
| Emergency stop | Self-locking switch with which immediate stopping of the door drive can be triggered in case of danger. The door drive remains in its current position until the user releases the emergency stop switch again, thus terminating the emergency stop situation. |
| Emergency lock | When the emergency lock is triggered, the door is closed and locked. The activations and safety devices are deactivated during the closing process. |
| Reset | Push button for restarting the drive after the operating voltage has been switched on or after a fire alarm has been terminated. When the push button is pressed, the self-retention integrated in the drive is activated, causing the drive to be activated. |