9.1 Single door narrow header mounting plate installation

9.1.1 Position header tracks

• Slide header tracks (7) to side of header with operator axle hole.

9.1.2 Fasten mounting plate to header tracks

1. Place mounting plate on header tracks, aligning holes in header track with 1/4 x 20 UNC mounting plate holes.
2. Thread eight 1/4-20 x 1" FHMSP into mounting plate hole locations (See Fig. 9.1.3). Do not tighten screws yet.

9.1.3 Fix location of mounting plate and secure to header

1. Slide mounting plate to dimension shown between inside edge of jamb bracket and edge of mounting plate (See Fig. 9.1.4).
2. Tighten all eight screws using No. 3 Phillips screwdriver. Recheck dimension in step 1.

9.1.4 Install third guide pin

1. Install third guide pin (6).

9.2 Double door narrow header mounting plate installation

9.2.1 Install mounting plates in double header

1. Reference Para. 9.1 for mounting plate installation.

9.2.2 Install Power connect cable

1. Route Power connect cable through both mounting plate channels.
2. Reference Para. 2.4 for Power connect cable lengths.

9.2.3 Install third guide pin

• Install third guide pin in each mounting plate (See Fig. 9.2.2).

9.3 Customer 115 Vac connection to mounting plate terminal block

9.3.1 Connect 115 VAC wiring

1. Route wiring into header, use appropriate fitting to secure conduit or wiring to header, and route wiring to 115 Vac terminal block.

• Terminate 115 Vac wiring at terminal block.

• Terminate ground wire at ground terminal. Remove nut and washer on ground terminal, bend ground wire around terminal, replace washer and nut and tighten. Leave service loop in ground wire. Use 5/16" [8 mm] socket for nut.

9.4 Double door header 115 Vac mounting plate connection

9.4.1 115 Vac connection to double door header

• Customer 115 Vac can connect to either mounting plate 115 Vac terminal block and ground stud.

9.5 Remove protective film strips from ED operator

9.5.1 Remove protective film strips

1. Remove two protective film strips from operator heat conductive pads.

9.6 Install ED100/ED250 operator on mounting plate in header

9.6.1 Install operator on mounting plate

1. Place operator over the three mounting plate guide pins.
2. Move operator in toward mounting plate, guiding all wiring into operator housing.
3. Once operator is placed flush against mounting plate, use a 5 mm T handle hex key to thread eight M6 SHCS into mounting plate.
4. Tighten all eight SHCS.
5. Insert 115 Vac mounting plate plug into operator 115 Vac socket.

9.7 Double door header ED100/ED250 operator installation

9.7.1 Install operators on mounting plates

• Refer to Para. 9.6 for installation of ED100/ED250 operators.

9.7.2 Connect 115 Vac power connect cable to both operators

Refer to Para. 9.2 for installation of power cable in mounting plates.

1. Insert power connect cable 115 Vac plug into socket on power switch board.
2. Remove ground stud nut (5/16" [8 mm] socket) and washer.
3. Insert power connect cable ground wire ring terminal on ground stud.
4. Replace washer, install ground stud nut and tighten.

9.8 Install ED50 operator on mounting plate in header

9.8.1 Install operator on mounting plate

1. Place operator over the three mounting plate guide pins.
2. Move operator in toward mounting plate, guiding all wiring into operator housing.
3. Insert 115 Vac mounting plate plug into operator 115 Vac socket.
4. Once operator is placed flush against mounting plate, use a 5 mm T handle hex key to thread eight M6 SHCS into mounting plate.
5. Tighten all eight SHCS.

9.9 Double header ED50 operator installation

9.9.1 Install operators on mounting plates

• Refer to Para. 9.8 for installation of ED50 operators.

9.9.2 Connect 115 Vac power cable to both operators

1. Insert power cable (Fig. 9.7.4) 115 Vac plug into socket on power switch board.
2. Remove ground stud nut (5/16" [8 mm] socket) and washer.
3. Insert power cable ground wire ring terminal on ground stud.
4. Replace washer, install ground stud nut and tighten.

9.10 Connect cables to ED50/ED100/ED250 operator

9.10.1 Connect mode switch cable to operator

• Carefully insert cable connector into header connector on operator.

9.10.2 Install RJ45 mode switch comm cable

1. Connect one end of cable to program switch panel RJ45 connector.
2. Connect other end of cable to COM 1 service connector on operator.

9.11 Double door header operator legend plate

9.11.1 Reverse legend plate orientation

1. Remove and reverse orientation of legend plate on RH operator so that letters face upward.
2. Reinstall legend plate.