Next section
Next page: →
System Setup & Specifications
Operator Specifications
| System | Description | Order No. |
|---|---|---|
| ED 100 | Swing door operator 230 V, EN 2 - 4 (push-version), EN 2 - 4 (pull-version) | 29222316 |
| ED 250 | Swing door operator 230 V, EN 4 - 7 (push-version), EN 4 - 6 (pull-version) | 29202316 |
System Components
The example system is equipped with all available components, selected in accordance with the door-leaf width and weight.
- 01 Mains switch
- 02 Mains connection
- 03 Connection unit
- 04 Axle connection on both sides
- 05 Operator system (motor/gear/spring)
- 06 Adjustment of closing force
- 07 Control unit
- 08 Switching power supply unit
- 09 Slot for dormakaba Upgrade Cards
- 10 User interface with information display
- 11 ED Cover Basic RM*
- 12 Internal program switch
- 13 Slide channel (set)*
- 14 Standard arm*
- 15 Slide channel CPD (set)*
- 16 Complete cover*
*supplied separately
Torque Overview
| Way of mounting | Lintel mounting on hinge side with slide channel (pull-version) |
Lintel mounting on opposite hinge side with standard arm (push-version) / slide channel (push-version) |
||||||
|---|---|---|---|---|---|---|---|---|
| ED 100 | ED 250 | ED 100 | ED 250 | |||||
| Min | Max | Min | Max | Min | Max | Min | Max | |
| Closing force EN 1154 | EN 3 | EN 4 | EN 4 | EN 6 | EN 3 | EN 4 | EN 4 | EN 7 |
| Manual closing torque (Nm)*** | 18 | 37 | 26 | 65 | 18 | 37 | 26 | 90 |
| Automatic closing force (N)** | 20 | FE: 150 LE: 67 |
20 | FE: 150 LE: 67 |
20 | FE: 150 LE: 67 |
20 | FE: 150 LE: 67 |
| Manual opening torque (Nm) | 40 | 50 | 55 | 85 | 40 | 55 | 60 | 90 |
| Automatic opening force (N)** | 20 | FE: 150 LE: 67 |
20 | FE: 150 LE: 67 |
20 | FE: 150 LE: 67 |
20 | FE: 150 LE: 67 |
| Opening force with activated Power Assist function (N)* |
23 (approx.) | |||||||
FE = With Full-Energy or Fire Protection Upgrade Card, LE = Low-Energy standard operator without upgrade card
* Power-Assist function is adjusted to maximum (function is activated at 0° opening width)
** The force is activated by an automatic opening in AUTOMATIC mode.
*** By installing the push-version with slide channel, the forces are reduced by approx. 33%
Features & Operation Modes
Door Closer Mode & AUTOMATIC Mode
Users may choose between two operation modes: Door Closer and AUTOMATIC mode.
- Door Closer Mode (Parameter Hd = 1): The system is optimized for manual operation. With its optional Power-Assist function, it is tailored to predominantly manually-operated doors where a door closer function is desired.
- AUTOMATIC Mode (Parameter Hd = 0): Especially suitable for mainly automatic access via motion detector or pushbutton. The door reverses as soon as it runs into an obstruction while closing. On activation of this mode, wind load control is also available.
Although in AUTOMATIC mode, the doors are still ready for manual access. In this case, we would recommend the Push & Go function.
Wind Load Control
ED 100 and ED 250 operators are especially suitable for applications at exterior doors subject to varying wind loads and for interior doors separating rooms where different pressures prevail.
While in AUTOMATIC mode, the wind load control monitors the driving speed and adjusts it if it exceeds or falls below the adjusted value. In conjunction with the Full-Energy Upgrade Card, the operator provides a force of up to 150 N at the main closing edge to compensate for environmental influences. The electronic latching action is activated during the last 5° of the closing cycle to support the closing action.
Evacuation Function (EVAC)
Standard swing door operators switch off in the event of an alarm, meaning barrier-free access is no longer possible for heavy doors. When the EVAC function is activated, the drive does not switch off completely. Instead, it:
- Deactivates motion detectors.
- Optionally deactivates safety sensors.
- Switches from full to low energy mode.
The power-assist function can then be used without safety sensors to ensure barrier-free access. Additionally, a time-limited automatic opening via the night/bank signal is possible for 20 seconds.
Requirement: One Upgrade Card PROFESSIONAL per drive. Activated via feedback contact 43/3 (indicated internally with IN18).
Power-Assist Function
The Power-Assist function may be activated while the door is in door closer mode (Hd = 1). As soon as a user opens the door by some degrees, the servo function supports the manual opening cycle, automatically adapting to the adjusted door closer size.
The level of servo support is adjustable to meet requirements of DIN 18040, DIN Spec 1104, CEN/TR 15894, BS 8300/2100 and document “M”, even up to class EN 6.
The smallest adjustable opening torque amounts to 23 Nm / 5 lbf (unless hold-open is triggered or power fails). It enables barrier-free access during standard operation according to EN 1154.
Note: It is not possible to use this in conjunction with Push & Go or wind load control as these may affect easy manual opening.
Smoke Pressure Ventilation (SPV)
Doors are often exposed to pressure differences, particularly with smoke extraction and pressure ventilation systems. The SPV function provides an additional set of parameters to optimize the operator for pressure conditions prevailing in the event of an alarm.
Requirement: One Upgrade Card PROFESSIONAL per drive. Activated via feedback contact 43/3 (indicated internally with IN19). Parameters are set via the hand-held terminal.