1. Driving Cycle
| Parameter | Setting Range | Factory Default | Description |
|---|---|---|---|
| Closing speed | 0 - 40 (5 – 20 s) | 18 | Slider control with 40 steps |
| Opening speed | 0 - 40 (3 - 20 s) | 36 | Slider control with 40 steps |
| Acceleration | 0 – 40 (40 = max.) | 36 | Influences the start-up behaviour while opening and closing |
| Latch check | 0 – 40 | 0 | Earlier slow-down while closing elongates the length of run with minimal possible closing speed in the area of the last 20° (e.g. safeguarding against shearing edge) |
2. Time Delay Open
| Parameter | Setting Range | Factory Default | Description |
|---|---|---|---|
| Time delay open | 0 – 40 (0 – 60 s) | 2 | Effective with AKA, AKI and push to actuate 0 – 20: Steps of 1 s 21 – 40: Steps of 2 s |
| Time delay SSK | 0 – 40 (0 – 60 s) | 4 | Effective with SSK 0 – 20: Steps of 1 s 21 – 40: Steps of 2 s |
3. Drive
| Parameter | Setting Range | Factory Default | Description |
|---|---|---|---|
| Opening angle | 0 – 40 | 35 | The opening angle is estimated during the calibration run and is equivalent to the value of 40 |
| Collision | 0 – 40 | 20 | Influences the force for the reversing. 0: weak 40: strong |
| Brake | Without Closing position Opening position Open/closed position |
Without | No brake integrated or no brake wanted. Or holding brake options for open/closed states. |
| Types of arms | Standard arm Sliding pulling Sliding pushing Inheader |
Standard arm | Standard arm for pushing opening / Sliding arm for pulling opening / Sliding arm for pushing opening / Special application (for USA only) |
| Inverse | Disabled / Enabled | Enabled | Opening of the door by spring tension in case of power failure. |
| Spring type | Display only | EN 4 | Springiness value is estimated during calibration run (MF 6. light pulse). Control with FPC 902: EN 4: 35-41 EN 5: 42-59 EN 6: 60-89 Display Unknown if out of range. |
| Limit open | Disabled / Enabled | Disabled | Enabled: The door hold is stronger in the open position. |
4. Entrance System
| Parameter | Setting Range | Factory Default | Description |
|---|---|---|---|
| Fire alarm | Disabled / Enabled | Enabled | Enabled: specific adaptation for the requirement of the EN-norms for fire doors. |
| Control | Single control Master control Slave control |
Single control | This setting is effected automatically under operating conditions. Simulation or Master/Slave-Control can be set with the FPC 902. |
| Interlock type | Without interlock | Without interlock | Function not yet integrated |
| Door type | Basic operator USA USA Low Energy UK UK Low Energy |
Basic operator | Frequently-used door types can be chosen for specific applications. |
5. Master/Slave 2 Door Leaves
| Parameter | Setting Range | Factory Default | Description |
|---|---|---|---|
| Function | AKA Master + Slave Master only Entry |
Master + Slave | AKA is effective on both operators, or only master operator while AKI/SSK operate on both. |
| Overlap | 0 - 40 | 5 | Only one door leaf moves in the pre-set overlap region. Stationary leaf waits during opening/closing. |
| Open sequence | 0 - 40 | 5 | Delayed start-up of the stationary leaf |
| Close sequence | 0 - 40 | 20 | Delayed closing of the moving leaf. (0 = synchronous activity). |
6. Manual Control
| Parameter | Setting Range | Factory Default | Description |
|---|---|---|---|
| During closing | Disabled / Enabled | Disabled | Enabled: The door closes motor-guided only with spring tension. |
| When locked | Disabled / Enabled | Disabled | Enabled: When locked, it can be opened manually without auto closing (night-watchman mode). |
| When automatic | Disabled / Enabled | Disabled | Enabled: When in automatic mode, it can be opened manually without auto closing. |
| Collision | Disabled / Enabled | Disabled | Enabled: If obstructed over 1s, it re-opens with motor force. |
| Support during closing | Disabled / Constant / Cumulative / Final bang / Slowly, cumulative / Slowly, final bang | Disabled | Varying types of motor closing force adjustments during the last 2° - 10° of closing process. |
| Active sensors | Disabled / SIS disabled / SIS enabled | Disabled | Controls active sensor configurations including or excluding SIS. |
| Closing speed | 0 - 40 | 20 | Slide control with 40 steps, depending on adjusted spring force. |
7. Control Panel
| Parameter | Setting Range | Factory Default | Description |
|---|---|---|---|
| Mechanical panel (BDE-M) | 3-digit (AUTO) 4-digit 3-digit (OFF-A) 3-digit (OFF-M) 3-digit (LOCK-A) 3-digit (LOCK-M) |
3-digit (AUTO) | Operational panel configurations for Manual, Automatic, Con. open, Locked and OFF switch combinations. |
| BDE-D (Language) | Deutsch / Français / English / English US | English | Language for the text output |
| Keyboard | Normal / OFF-Mode | Normal | Standard-Function or Special mode where Locked mode is replaced by OFF. |
| Contrast BDE 1 & 2 | 0 - 40 | 0 | Contrast settings for respective BDE displays. |
| Light time | 0 - 40 | 0 | 0: No backlight. 1-39: Backlight seconds. 40: Continuous. |
8. Locking, Interlock, & I/O
| Category | Parameter | Setting / Range | Factory Default | Description |
|---|---|---|---|---|
| LOCKING | Locking function | Normally locked / Always locked | Normally locked | Configures when VRR interlock is operated (permanently active vs lock button-based). |
| Lock type | Standard / Locking bolt / Magnet / Pulse | Standard | Configuration for electronic lock type (e.g. eff-eff, motor-lock). | |
| VRR manually | Disabled / Enabled | Disabled | Approved for manually closed doors. Protects actuators based on lock reverse signal. | |
| Start delay | 0 - 40 (0 - 8 s) | 0 | Application for motor locks without reverse signal on VAK. | |
| INPUT | AUX1_IN | Disabled / BEA Bodyguard | Disabled | Special safety function (USA only) |
| AUX2_IN | AKA / Railbeam | AKA | Special function (USA only) | |
| OUTPUT | AUX1_OUT | Disabled / BEA Bodyguard / Test sensors | Disabled | Special function, including safety sensors with integrated test input. |
| MISCELLANEOUS | Push to actuate | Disabled / Normal / Slow / Manually operated | Disabled | Configures motor reaction variables and wind pressure compensation behavior. |