4. Maintenance
4.1 Checking the door unit
Power-operated doors have to be tested by a qualified individual at least once a year.
Power-operated doors on escape and emergency routes have to be tested by a qualified individual at least twice a year.
The test is carried out according to the supplied inspection log for power-operated doors.
Between tests by a qualified individual, it is recommended as an additional safety precaution that a regular inspection of the key functional elements be performed by the facility operator.
4.2 Wear parts
Using the wrong replacement parts can cause a risk of injury!
The use of incorrect or faulty replacement parts can be dangerous to personnel.
- Only use replacement parts approved by dormakaba.
The replacement of wear parts depends on the expected number of load changes made by the door unit. ES PROLINE sliding door operators are tested on approval with 1 or 1.5 million opening and closing cycles. However, during operation the door units are subjected to other environmental conditions and a natural ageing process. As such, dormakaba prescribes timings for the replacement of safety-related wear parts in order to ensure safe operation of the door unit.
| Wear parts | Replacement at the latest |
|---|---|
| Rollers | 2 years |
| Counter rollers | In the event of visible wear |
| End stop | In the event of visible wear |
| Toothed belt | 5 years |
| Battery pack | 3 years |
| Track profile | 5 years |
| Anti-static brushes | 1 year |
| Locking contact | 4 years |
| CO48 rubber cord | 1 year |
| Li-Mn button cell CR 1220 | 8 years |
4.3 Replacing the battery pack/the battery
The battery pack and the battery may only be replaced by trained specialists according to the corresponding manual.
5. Maintenance by dormakaba
Regular maintenance of your units pays off: weak points are detected and eliminated at an early stage and your unit’s service life is increased.
dormakaba and our authorized partners offer premium maintenance service for automatic doors and hold-open systems, which gives building operators reliable safety through the official seal of approval. Because if all door units have not been properly tested, the building operator may be liable for property damage and personal injury in the event of an accident.
Regardless of safety aspects, regular maintenance also makes sense from an economic point of view. Any damage or wear can thus be detected and repaired at an early stage. The risk of unforeseen costs, such as high repair costs, can be minimized – and we help you to keep an eye on your budget – always with the aim of increasing the service life of your door units.
dormakaba takes over the complete organization and execution of maintenance for you. The advantage to you: All units – including units from other manufacturers – are tested by trained experts at the scheduled regular intervals. The facility operator does not have to worry about anything else and legal requirements are reliably fulfilled.
Maintenance Contract: A maintenance contract for the door ensures tested functionality with a premium standard! We want to win you over too – contact us for a non-binding, free quote.
6. Troubleshooting
Malfunctions can have many causes. As the cause often lies in the ambient conditions, the operator attempts to detect the ambient conditions and react to them accordingly. This involves the operator interrupting the current function and starting again after a waiting time or a new activation. If this does not work, the automatic operator function switches off and an error message is output.
The display is an LED on the operating mode switch. The display flashes or shows a continuous light and indicates a malfunction that must be rectified by dormakaba Service.
To reset error messages, switch the operating mode switch to the OFF position. Before acknowledging an error message, cause analysis and removal shall always take place.
6.1 Influence of weather conditions
The safety sensors on the door unit protect the passage area. Personal protection takes top priority when setting the sensitivity of the sensors.
Weather factors such as rain or snow, flying foliage or sunlight on reflective flooring can cause the sensors to make false detections.
False detections can result in the door opening for up to 1 minute. This opening of the door unit is stipulated in a standard and is intended solely to protect door users.
6.2 Error location
If faults occur during operation, check the following:
- Is the power supply available?
- Is the optional emergency stop switch released?
- Is the optional emergency open switch released?
- Is the operating mode switch in the correct position?
- Are objects blocking the door?
- Are the door leaves smooth-running?
If these items are all OK and the door unit is still not functioning, notify dormakaba Service.
7. Disassembly, recycling and disposal
Disassembly is carried out in the reverse order of mounting and must be carried out by qualified personnel.
Work on electrical units must only be carried out by qualified electricians.
- Before starting work on electrical units and equipment, establish a voltage-free state and maintain this state for the entire duration of the work.
The product must be disposed of in an environmentally friendly manner. Electrotechnical parts and batteries must not be disposed of as domestic waste. Dispose of electrotechnical parts and batteries in the designated acceptance and collection points. Refer to the statutory regulations for your country.
8. EC declaration of conformity
dormakaba Deutschland GmbH, DORMA Platz 1, 58256 Ennepetal hereby declares that the products:
ES 250 PRO, ES 250 PRO FST, ES 250 PRO T, ES 250 PRO T FST, ES 400 PRO, ES 400 PRO FST, ES 400 PRO T, ES 400 PRO T FST, ES 500 PRO, ES 250 PRO EASY, ES 250 PRO EASY T
are in conformity with the provisions of the following EC Directives and that the following standards have been applied.
EC Directives:
- 2014/30/EU Electromagnetic Compatibility
- 2011/65/EU RoHS
Harmonized European standards, national rules:
- EN 13849-1
- EN ISO 12100
- EN 16005
- EN 60335-2-103
- EN 61000-6-2
- EN 61000-6-3
- EN 61000-3-2
- EN 61000-3-3
- EN IEC 63000
System components / Expansion modules: Operating mode switch (BAS), safety and activation (SIAK), inputs and outputs (I/O)
9. EC declaration of incorporation
dormakaba Deutschland GmbH, DORMA Platz 1, 58256 Ennepetal hereby declares that the partly completed machinery (Products as listed above) conforms to the following essential requirements of the Machinery Directive (2006/42/EC) - Annex I, Article:
1.1.3, 1.1.5, 1.2.1, 1.2.3, 1.2.5, 1.2.6, 1.3.2, 1.3.3, 1.3.4, 1.3.8.1, 1.3.9, 1.5.1, 1.5.2, 1.5.4-1.5.10, 1.5.16, 1.6.1, 1.6.2, 1.6.3, 1.6.4, 1.7.1.1, 1.7.3, 1.7.4
The partly completed machinery continues to comply with all relevant provisions of Directives 2014/35/EU and 2014/30/EC.
The specialist technical documents have been created and are available from the Product Compliance Manager .
10. UKCA Declaration of Conformity
This declaration is issued under the sole responsibility of the manufacturer. dormakaba Deutschland GmbH declares that the products comply with the provisions of the applicable legislation and the designated standards of the United Kingdom.
UK legislation:
- Electromagnetic Compatibility Regulations 2016
- RoHS, The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Regulation 2012