Dorma ED100 & ED250 Parameters: Setup & Configuration Guide

Defines the installation configuration.

• 0: Frame reveal mounting hinge side, slide rail pulling EN 4-6
• 1: Frame reveal mounting opposite side to the hinge, scissor arm pushing
• 2: Frame reveal mounting opposite side to the hinge, slide rail pushing
• 3: OHC_R (Overhead Concealed Right)
• 4: OHC_L (Overhead Concealed Left)
• 5: Frame reveal mounting opposite side to the hinge, scissor arm pushing EN7
• 6: Frame reveal mounting hinge side pulling with CPD lever
• 7: Frame reveal mounting hinge side pulling with CPD 250 lever

The frame reveal depth is set in 10 mm increments. The required dimensions can be found in the assembly drawings.

The rebate is included in the door leaf width. The door width is specified in 100 mm increments.

• 0: Single-leaf door
• 1: 2-leaf door, active door leaf, overlapping door leaf
• 2: 2-leaf door, passive door leaf, overlapping door leaf
• 3: 2-leaf door, active door leaf, edgeless door leaf
• 4: 2-leaf door, passive door leaf, edgeless door leaf

The opening speed refers to automatic operation. Country-specific limits must be adhered to and checked after setting. The full setting range is only available with an installed Full Energy Upgrade Card. The admissibility of the setting is checked by internal monitoring.

The closing speed refers to automatic operation. Country-specific limits must be adhered to and checked after setting. The full setting range is only available with an installed Full Energy Upgrade Card.

The time the door remains open for people to pass through. Starts after contact/voltage is opened at inputs (activator, safety, Push & Go) and door is open. In Low Energy mode, min. 5s is recommended. Increments: 1s (0-30s), 5s (>30s).

Specific hold-open time for key switch/night bank inputs.

Applies after purely manual opening, including Power Assist activation or stop by sensor strip.

Input signal from hinge side safety sensor is ignored beyond this angle. Required when door opens against a wall/obstacle. Minimize this area for personal protection. A quick-flashing point on display indicates blanking is active when exceeded.

Configures testing for safety sensors (e.g., IRS-2, EN 16005, DIN 18650). Level (high/low active) must match the sensor.

• 0: Test Off (for IRS-2)
• 1: BS test sensor - level high active
• 2: BGS test sensor - level high active
• 3: BS & BGS test sensor - level high active
• 4: BS test sensor - level low active
• 5: BGS test sensor - level low active
• 6: BS & BGS test sensor - level low active

• 0: Signal ignored when door is closed.
• 1: Safety sensor can trigger opening impulse when closed.

• 0: BS safety sensor not active during initial travel (hidden).
• 1: BS safety sensor active during initial travel.

Delay before door opens after pulse. Setting "0" means no "pressing" before unlocking.

Strength of push in CLOSED direction before opening. Relieves limit electric strike releases. Higher values increase arm load; keep as low as necessary.

Tests Power Reserve module (for SVP-2000 DCW / M-SVP 2000 DCW). Automatically activated if fire protection module is detected. Test runs every 24h.

• 0: Test off
• 1: Test active

Basic parameter for wind load control. Check actual forces on door leaf after learning cycle to meet local standards.

Basic parameter for wind load control. Check actual forces on door leaf after learning cycle to meet local standards.

Motorized end stop action to overcome seals/locks. Increase cautiously to avoid damage.

Angle from which motorized end stop pulse is effective.

Force applied permanently after end stop to hold door CLOSED against wind. 0=Off, 1-9=On.

If ON (1), door opens automatically if manually moved 4 degrees from CLOSED. Requires "hd" (door closer mode) to be 0.

• 0: Internal program switch active.
• 1: External program switch (contacts). Internal plug removed.
• 2: External DCW program switch. Internal plug removed.
• 3: Via TMS software.
• 4: Via Door Pilot interface, TMS, or DCW.

• 0: Returns to last known position.
• 1: Switches to OFF position (insurance-related lock requirement).

• 0: Immediate function takeover.
• 1: 10s delay. Useful if passing through detector after changing door settings.

• 0: Door locked at CLOSED position.
• 1: Door not locked in automatic mode at CLOSED. Locking contact remains switched permanently (requires 100% duty cycle opener).

• 0: Deactivated.
• 1: Switches at CLOSED position.
• 2: Switches at OPEN position.
• 3: Faults reported.
• 4: Door CLOSED and locked.
• 5: Fault or information reported.
• 6: Switches when open further than status contact angle.

• 0: Independent of contact 4/4a.
• 1: Switches as soon as 4/4a opens. Impulses 100% duty-opening time required. Not for DCW motor locks.

Displayed in steps of 10,000. Display 4 = 40,000. 99 = 990,000+.

Set to 1 to delete memory. Automatically resets to 0.

Set to 1 to reset cycle/time counter to 200,000 cycles / 12 months.

Triggered by pressing Fact Setup key > 8s.

• 1: Standard. All parameters default. Upgrade cards retained.
• 2: Extended. All parameters default. Upgrade cards deleted from memory.

• 0: Automatic mode. Optimized for motion detectors/safe closing. Reverses on blockage.
• 1: Door closer mode. Mainly manual opening. Stops on blockage. Optimized for manual open. Power Assist only available here.

Available Cards:

• Fire Protection: Required for fixed systems (EN 14637). Enables detector input. Activates Full Energy automatically.
• Full-Energy: Unlocks full adjustment range for speed/force.
• Professional:
  • Power Surge: Door control without hold-open time (toggle open/close).
  • Extended Hold-open: 0-180s.
  • Nurse/Beds: Separate/joint opening of 2-leaf doors.
• EVAC / SPV: Emergency/Smoke control modes. Input 43 control.
• Disabled WC: Accessibility functions.
• DCW: Enables DCW bus components (program switches, motor locks, etc).