Next section
Next page: →7.1 Narrow Header (4" x 6") – Push Arm Template
7.1.1 Axle distance "A"
Definition: Bottom of header to bottom edge of door frame.
Formula: Header width = Door width + 3”
| Axle Extension | ED50 / ED100 | ED250 A |
|---|---|---|
| Arm (Standard) | - | 0" |
| 20 mm | - | 1/8" |
| 30 mm | - | 1/2" |
| 60 mm | - | 1 5/8" |
| 90 mm | - | 2 7/8" |
7.2 Narrow Header (4" x 6") – Deep Push Arm Installation Template
7.2.1 Axle distance "A"
Definition: Bottom of header to bottom edge of door frame.
Formula: Header width = Door width + 3”
| Axle Extension | ED50 / ED100 | ED250 A |
|---|---|---|
| Arm (Standard) | - | 0" |
| 20 mm | - | 1/8" |
| 30 mm | - | 1/2" |
| 60 mm | - | 1 5/8" |
| 90 mm | - | 2 7/8" |
7.3 Narrow Header (4" x 6") – Pull Arm Template
7.3.1 Axle distance "A"
Definition: Bottom of header to bottom edge of door frame.
Formula: Header width = Door width + 3”
| Axle Extension | ED50 / ED100 | ED250 A |
|---|---|---|
| Arm (Standard) | - | 7/16" |
| 20 mm | - | 1 1/4" |
| 30 mm | - | 1 5/8" |
| 60 mm | - | 2 7/8" |
| 90 mm | -- | 4" |
7.4 Narrow Header (4" x 6") – Deep Pull Arm Template
7.4.1 Axle distance "A"
Definition: Bottom of header to bottom edge of door frame.
Formula: Header width = Door width + 3”
| Axle Extension | ED50 / ED100 | ED250 A |
|---|---|---|
| Arm (Standard) | - | 7/8" |
| 20 mm | - | 1 5/8" |
| 30 mm | - | 2" |
| 60 mm | - | 3 1/4" |
| 90 mm | -- | 4 3/8" |
7.5 Center Hung Pivot Door, Narrow Header (4" x 6"), Push Arm Template
7.5.1 Axle distance "A"
Definition: Bottom of header to bottom edge of door frame.
Formula: Header width = Door width + 3”
| Axle Extension | ED50 / ED100 | ED250 A |
|---|---|---|
| Arm (Standard) | - | 0" |
| 20 mm | - | 5/8" |
| 30 mm | - | 1" |
| 60 mm | - | 2 1/8" |
| 90 mm | -- | 3 1/4" |
Para. 10.2.10. The opening at hinge side of center pivoted swinging doors shall be:
- a) Less than 1/4" wide with the door in any position, or
- b) At least 3/4" wide with the door in any position.
A door that does not comply with the above is acceptable if provided with a finger guard.
7.6 Center Hung Pivot Door, Narrow Header (4" x 6"), Pull Arm Template
7.6.1 Axle distance "A"
Definition: Bottom of header to bottom edge of door frame.
Formula: Header width = Door width + 3”
| Axle Extension | ED50 / ED100 | ED250 A |
|---|---|---|
| Arm (Standard) | - | 1/4" |
| 20 mm | - | 1" |
| 30 mm | - | 1 1/2" |
| 60 mm | - | 2 5/8" |
| 90 mm | -- | 3 7/8" |
Para. 10.2.10. The opening at hinge side of center pivoted swinging doors shall be:
- a) Less than 1/4" wide with the door in any position, or
- b) At least 3/4" wide with the door in any position.
A door that does not comply with the above is acceptable if provided with a finger guard.