7.1 Arm System, PUSH
Art. No. 1007241BK/SIPUSH: As a commonly replaced component among assa abloy parts, it is used if the assa abloy sw100 operator is wall mounted on the opposite side compared with the opening direction and that the unit must be approved for fire applications.
7.1.1 PUSH-arm Extensions
345 mm extension
Art. No. 173005BK/SI| Extension Type | Reveal Range (A) |
|---|---|
| None (standard arm) | 0 - 100 mm |
| 345 mm extension | 100 - 215 mm |
| 230 mm + Joint part | 215 - 305 mm |
230 mm extension
Art. No. 173004BK/SIJoint part
Art. No. 1731917.2 Arm System, PUSH-335
Art. No. 1007965BK/SIPUSH-335: It is used if the besam sw100 operator is door leaf mounted and mounted on the hinge side of the door.
7.3 Arm System, PULL
Art. No. 1008401BK/SIPULL: It is used if the operator is installed on the wall on the same side as the door swing.
7.4 Arm System, PULL-220
Art. No. 1011998BK/SIPULL-220: It is used if the operator is installed on the wall on the same side as the door swing and when the door is 450-700 mm wide.
7.5 Reveal Spacer: PULL / PULL-220
Art. No. PULL1014317BK/SI- 40 mm (1-9/16")
- 60 mm (2-3/8")
7.6 20 mm Extension
Art. No. 1011205Extension 20 mm for PULL/PAS and lower mounting of slide track profile.
7.7 Drive Shaft Extension Kits
| Size | Art. No. |
|---|---|
| 20 mm (3/4") | 173109BK / 173109SI |
| 50 mm (2") | 173108BK / 173108SI |
| 70 mm (2-3/4") | 173107BK / 173107SI |
Lower adapter M8: Used for 20 mm lower installation height. Art. No. 1007618
7.8 Control Switches
7.8.1 ON/OFF/HOLD Open Switch (will not operate electric lock)
P/N: 1003582| Function | Position/Wire | Description |
|---|---|---|
| ON | White | Impulses from activation units connected to XIMP are forwarded into inner impulse. |
| OFF | Brown | Impulses from activation units connected to XIMP are not forwarded into inner impulse. These units cannot open the door. |
| HOLD | Green | The door is held permanently open. |
7.8.2 4-Position Switch PS-4C (operates the electric lock)
Art. No. 655845| Selection | Position | Function Description |
|---|---|---|
| OFF | The door is closed. | The door cannot be opened with inner and outer activation units. The door is locked if an electromechanical locking device has been fitted. The door can be opened with a key switch (if fitted). |
| EXIT | Passage from inside only. | The door is normally locked if an electromechanical locking device has been fitted. The door can only be opened with the inner activation unit and with a key switch (if fitted). |
| AUTO | Normal position. | The door can be opened with the inner and outer manual and/or automatic activators. The electric strike, if fitted, is open. |
| OPEN | Hold Open. | The door is held permanently open by the motor. |
7.9 Sync Cable for Double Doors (Synchronizing of 2 Operators)
Note! Connect a cable between primary CU and secondary CU. The connection/marking of the sync cable determines which of the operators is the primary and secondary.
- Rebated door: Primary door must open before secondary; secondary must close before primary.
How to Cut the Jumper for Double Doors
| Secondary Side Jumper | Primary Side Jumper | Jamming | Rebated | Closing Function | Opening Function |
|---|---|---|---|---|---|
| No cutting | No cutting | No | No | Synchronous | Synchronous |
| No cutting | Cut black | No | Yes | Asynchronous | Synchronous |
| Cut red | No cutting | Yes | Yes | Asynchronous | Asynchronous |
| Cut red | Cut black | - | - | Double egress | |
Settings for Double Doors
| Function | Secondary Side | Primary Side | Common/Individual |
|---|---|---|---|
| Program selection | X | X | Common |
| Opening time, Closing time, Hold open time | X | X | Common |
| Close/Continue to open when obstructed | X | X | Common |
| PAG On/Off | X | X | Common |
| Level of Power assist | (X)* | X | Common |
| Lock/Unlock signal voltage | X | X | Individual |
| Locked without/with power | X | X | Individual |
* For "Double egress doors", these functions must be set separately for primary and secondary.
7.10 Extension Units
For installation see page 45.
EXU-SA (Kit for Safety Functions)
Art. No. 1003557EXU-SI (Kit for Security Functions)
Art. No. 1003554AIU (Audible Warning Signal)
Art. No. 65608324 V DC
7.11 Battery Backup Unit
Art. No. 1003567
Warning: Disconnect mains when replacing battery. Risk of explosion if wrong type of battery is used.
7.12 Cover Piece Kit
Art. No. 1009935BK/SI7.13 Labels
- Label kit (including all below): Art. No. 1005227
- Emergency break-out, DIN right door: Art. No. 1001785
- Emergency break-out, DIN left door: Art. No. 1001786
- Activation by disabled people: Art. No. 1003963
- Operator designed for disabled people: Art. No. 1003964
- Supervision of child: Art. No. 1001695
- ASSA ABLOY door sticker: Art. No. 1700038