Next section
Next page: →6.1 Connecting the drive
WARNING!
Risk of fatal injury due to electric shock!
Risk of fatal injury due to electric shock!
- The electrical system (230 V) may only be connected and disconnected by a qualified electrician or a qualified electrician for specified tasks.
- Carry out mains connection and earth conductor test in accordance with VDE 0100 Part 600.
- Strip insulation from the mains cable (4) max. 40 mm.
Dimensions Reference:
- 9 mm
- PE 9 mm
- max. 30 mm
- 10 mm
- Strip the mains cable (4).
- Insulation stripping length 40 mm
- Stripping length 9 mm
- PE line lead 10 mm
- Connect the drive to the 230 V mains network.
- Switch the main switch (2) on at the transformer (3).
- Insert the rechargeable battery connector (1) at the control unit.
- Carry out the production test as described in the wiring diagram “Automatic sliding doors DCU1-NT/DCU1-2M-NT”.
6.2 Mounting the cover
WARNING!
Danger of injury! People can be injured when handling the cover.
Danger of injury! People can be injured when handling the cover.
- Always make sure two people handle the cover.
WARNING!
Danger of injury from falling cover!
Danger of injury from falling cover!
- Make sure that the cover is attached along the entire length of the track.
- Release the cover carefully and check whether it has been suspended safely.
- Unscrew the locking pin (1) from the tooth belt locking mechanism (optional).
6.2.1 Mount the cover suspension piece
- Slide the cover suspension piece (1) into the upper or lower screw duct of the cover (2).
- Secure the cover suspension piece (1) on the right and left at a distance of approx. 50 mm from the end of the cover using 2 screws (tightening torque max. 1.5 Nm).
- Push the cords (rubber cables) (3) onto the mounted suspension pieces (1) of the cover.
6.2.2 Mounting the side panel suspension piece
- Screw the side panel suspension piece (2) using the oval head screw (3) into side panels (1) left and right (tightening torque 1.5 Nm).
6.2.3 Fitting the cover earthing
- Before installing the cover earthing, check whether the cover suspension piece (1) has been fitted.
- Knock the locating pin for the cover earthing (2) on the side of the earthing approx. 30 mm into the upper screw duct.
6.2.4 Hook the cover catch rope in place
- Hook the cover catch rope (2) on the cover suspension piece (3) in the cover (4).
- Hook the cover catch rope (2) on the suspension piece (1) of the side panels.
6.2.5 Connecting cover earthing
- Connect the earthing cable (2) of the cover using the plug-in connection of the device flat plug (1).
Depending on the length of the drive, a 2nd device flat plug must be fitted for hood earthing, in order to bridge the gap between the transformer earthing and the cover earthing.
6.2.6 Sliding the cover in place
- Slide the cover (1) onto the side panels (3) until it latches in and ensure that it is also seated correctly in the area of the module mounts and cable guides.
- Check the correct position of the cover catch ropes (2) and the earthing wire. There must not be any contact with moving parts.
- Turn the locking pin (4) into the tooth belt locking mechanism (optional). Following installation the locking pin (4) must be positioned in the hole of the cover in such a way that the locking mechanism can be locked and unlocked.
- If necessary, enlarge the drill hole (5) in the cover.
6.3 Mounting the safety devices
For information about connection and parameter setting of the safety sensors, and the inputs and outputs and on commissioning, please refer to the wiring diagram.
- Mount safety and activation equipment.
- Route cables properly in cable ducts.
For electrical installation, see wiring diagram.
6.4 Installing operating elements/switches/push buttons
For electrical installation, see wiring diagram.
- Install the operating elements in such a way that users cannot stand in hazardous areas.
6.5 Commissioning the door system
For information about connection and parameter setting of the safety sensors, and the inputs and outputs and on commissioning, please refer to the wiring diagram.
6.5.1 Creating log book
- Carry out a safety analysis.
- Record installed options in the safety analysis for the operator.
6.6 Dismantling
WARNING!
Risk of fatal injury due to electric shock!
Risk of fatal injury due to electric shock!
- The electrical system (230 V) may only be disconnected by a qualified electrician or a qualified electrician for specified tasks.
WARNING!
Danger of injury! People can be injured when handling the cover.
Danger of injury! People can be injured when handling the cover.
- If the cover is more than 4 m long, always work in pairs when handling the cover.
CAUTION!
Danger of injury due to impact and crushing!
Danger of injury due to impact and crushing!
- Secure the moving leaves against unintentional movement.
- Disconnect the rechargeable battery.
Dismantling is done in the reverse order of installation.