GEZE Slimdrive SL NT Manual: Installation & Service

4.1 Diagrams

The diagrams are subject to change without notice. Use only the most recent version.

4.2 Tools and Aids

4.3 Torques

The torques are given at the respective installation step.

4.4 Components and Assembly Groups

See the ep-drawing for the required installation situation and drive drawings.

5.1 Preparations to be made on-site

Check the preparations made on-site by the customer to ensure proper installation:

• Type and load capacity of the façade construction or suspending frame
• Evenness of the installation surface
• Evenness of the finished floor level
• Cable plan requirements

5.2 Preparing the track

Pre-mounted systems are delivered with attached module mount.

• Remove the module mounts to make it easier to fix the track to the wall.

5.3 Mounting the track

• Protect the running surface from damage.

5.3.1 Mounting the intermediate plates

• Clip the intermediate plates (1) onto the rear of the track.
• Upper row of drill holes for wall installation.
• Lower row of drill holes for the clip of the intermediate plate.

Mounting can also be carried out conversely depending on the building structure (post design). Use the upper row of drill holes for fixing if possible.

5.3.2 Install the track

View from the side

• Determine the installation height of the track (2). Take unevenness of wall and floor into account.
• Align the track horizontally.
• Mark the fastening drill holes (1) (upper row of drill holes on the track).
• Remove the track.
• Drill the holes (1) for fixing.
• Install the brush profile with brush (3).
• Screw the track (2) in place.
• Install the sealing profiles (4).
• Press rubber seal into the draught sealing profiles.

With 1-leaf systems:

• Install the wall strips (5).

5.4 Mounting the floor guide

The selection of floor guide depends on the on-site conditions. One of the following floor guide options must be used. For further information see the respective installation drawing, Chapter 4.1.

5.4.1 Fitting angled floor guide for floor mounting (option)

Angled floor guide with moving leaf left hand slide to open:

• Screw the angled floor guide (6) in place using 2 suitable countersunk screws (1) and (2).

Angled floor guide with moving leaf right hand slide to open:

• Screw the angled floor guide (6) in place using 2 suitable countersunk screws (3) and (2).

Legend:

1. Countersunk screw for moving leaf left hand slide to open
2. Countersunk screw
3. Countersunk screw for moving leaf right hand slide to open
4. Outside
5. Inside
6. Angled floor guide

5.4.2 Adjustable angled floor guide for wall mounting (option)

• Screw the fixing bracket (2) to the fixed panel (1) using two screws (5) (torque 5 Nm).
• Align the moving leaf (6) and thus the adjusting angle (4) and tighten the screw (3) (torque 3 Nm).
• If there is no fixed panel available, mount the floor guide on the wall using suitable attachment material.

5.4.3 Continuous floor guide (option)

• See the component drawing "Continuous floor guide" on how to install the continuous floor guide.
• For further information see the respective installation diagrams, Chapter 4.1.

5.5 Installing the moving leaf

5.5.1 Fit the connecting arm

1-leaf

• Slide the clamping plate (1) into the connecting arm (only for 1-leaf doors).
• Slide the roller carriage (2, 4) into the connecting profile (3).
• Secure both roller carriages (2, 4) with 2 setscrews (5) each (torque 3 Nm).

2-leaf

• Secure the roller carriage (towards the secondary closing edge) with setscrews (5) (torque 3 Nm).
• Fasten the second roller carriage (towards the main closing edge) with the two screws for the driver (torque 5 Nm).
• The angled part (7) of the connecting arm must be facing the main closing edge.

5.5.2 Inserting roller carriage into the track

• Insert roller carriage (2) into the track (1).
• Insert the moving leaf mounting aid (3) to secure the roller carriage in the track.
• Slide the track-supporting rollers (4) upwards and tighten slightly using screws (5).

5.5.3 Install the supporting brackets on the moving leaf

The supporting brackets are installed during glazing of the moving leaves. In case of subsequent installation of the supporting brackets, the frames of the moving leaves must be dismantled (see installation instructions for moving leaves).

• See installation drawing for the moving leaf for the position of the supporting brackets (1).

5.5.4 Fitting the moving leaves

5.5.5 Adjusting the moving leaves

Adjust the parallel position and height of the moving leaves:

• Use the suspension bolts (1) to align the door moving leaves flush. Ensure the same level and parallel closing edges when doing so.
• Loosen the fixing screw for the height adjustment (2) and use the adjustment screw (3) to adjust the moving leaf height.
• 2-leaf: Adjust the height of both moving leaves.
• Tighten the screws (2) (torque 20 Nm).
• Tighten the screws (1) (torque 10 Nm).
• Tighten the screw (3) (torque 5 Nm).
• Note the shearing and pinching spots in accordance with DIN 18650 and DIN EN 16005, see safety analysis and diagrams in Chapter 4.1.
• Make the individual moving leaf move smoothly.

Adjusting the counter-roller:

The counter-roller (4) must have an upper clearance of 0.5 mm to the track (corresponds approximately to the thickness of 4 sheets of copy paper).

• Loosen the screw (5) on the rear of the counter-roller.
• Move the counter-roller until a clearance of approx. 0.5 mm is set.
• Tighten the screw (5) again (torque 10 Nm).

5.5.6 Mounting the short driver

Drivers must not touch any obstacle over the entire travel path. See the drive drawing for the precise position of the driver.

1-leaf:

• Mount the short driver (2) to the clamping plate (3) using 2 screws (1).
• Position the clamping plate (3) and short driver (2) on the connecting arm (see drive drawing for position).
• Tighten the screws (1) (torque 5 Nm).

2-leaf:

• Use 2 screws to screw the short driver (1) through the outer oblong holes to the left roller carriage (2) on the right moving leaf (torque 5 Nm).

5.5.7 Install the long driver (2-leaf)

• Use 2 pre-mounted screws to screw the long driver (1) through the outer oblong holes to the right roller carriage (2) on the left moving leaf (torque 5 Nm).
• Position the moving leaf in the closed position.