MotionSensor M A01

The MotionSensor M A01 acts as a motion detector for 1-leaf and 2-leaf door systems, suitable for both indoor and outdoor use. It requires no additional weather protection cap and is installed centrally above the door system.

Technical Data

Supply voltage

24 V DC +/-15%

Power input

< 2.5 W

Temperature range

-20 °C to +55 °C

Humidity

0 % to 95 % non-condensing

Protection class

IP54

Detection range

approx. 10 m x 4.5 m (at 2.2 m height, 30° angle)

Installation height

2 m to 4 m

Data interface

CAN dormakaba

Scope of Delivery

• MotionSensor M A01
• CAN connection cable
• Mounting kit for radar sensor

ED Connection Board CAN

The ED connection board CAN includes the Motion IQ Controller and provides CAN connection for the M A01 sensors. An RGB LED function display shows the current operating status and any faults. Parameterization is done via the ED operator interface.

Technical Data

Supply voltage

24 V DC +/-15 %

Power input

approx. 20 mA

Temperature range

-15 °C to +50 °C

Humidity

up to 93 %, non-condensing

Protection class

IP20

Note: The ED CAN Multi Adapter is required for use of MotionIQ on 2-leaf doors or an external PGS.

Connections

1. Lock (e.g., SVP)
2. Smoke detector (e.g., RM-ED)
3. Emergency-off function, cut-off operator function
4. RS232 connection socket (connection ED control)
5. Connection flat ribbon cable for ED control
6. Connection terminal CAN connection cable for radar sensors
7. Safety sensors hinge side and opposite hinge side
8. Signal input for access control, impulse outside and impulse inside

Article Number: 29256002

ED CAN Multi Adapter

The ED Multi Adapter allows connection of an external program switch (Off, Exit, Automatic, Permanently open functions) and actuation via an external voltage supply. The adapter also provides additional connection options for future CAN components.

Note: Combining with the BRC-R radio receiver is not possible.

Article Number: 29280061

CleanSwitch IP20 (Flush-mounted)

Contactless radar pushbutton, System 55 compatible, flush-mounted.

Protection class

IP20

Detection zone

Adjustable 10-50 cm

Dimensions

80 x 80 x 40 mm (Switch insert 55 x 55 mm)

Color

White

CleanSwitch IP65

Contactless radar pushbutton, System 55, compatible with conventional flush-mounted boxes.

Protection class

IP65

Detection zone

Adjustable 10-50 cm

Dimensions

80 x 80 x 38 mm (Switch insert 55 x 55 mm)

Color

White

Pushbutton (System 55)

Single-pole, changeover contact, single frame flush-mounted version, concealed.

Key Switches KT 3-1

1 NO contact, with profile half-cylinder (replaceable), key retractable only in neutral position. Aluminum/metal housing (75 x 75 x 60 mm).

Key Switches ST 32 DCW®

Tamper-proof key switch with LED display (red/green), silver-colored LM housing. Suitable for controlling TMS and SafeRoute door management systems. Programmable via TMS Soft.

Protection class

IP 54

Housing Dimensions

75 x 75 x 50 mm (approx.)

Front Plate Dimensions

90 x 100 x 2 mm (flush-mounted)

Article Number: 56343200

Key Switch CAN

Switch with single-pole changeover contact, Europrofile half-cylinder (DIN 18252). With cover for System 55. Requires ED firmware 3.3 or higher.

Note: Not suitable for surface-mounted boxes.

Access Control Pads

Silver Large Pushbuttons

Plastic Flat Design

Surface-mounted version, grey plastic.

Dimensions

209 x 79 x 17 mm

Article Number: 05080231332

Receiver BRC-R

The BRC-R radio receiver installs inside the operator. Up to 1024 transmitters can be allocated.

Article Number: 29302002

Transmitter Options